Opening a Device
Before using a device, you must initialize it by using the open (MCI_OPEN) command. This command loads the driver into memory (if it isn't already loaded) and retrieves the device identifier you will use to identify the device in subsequent MCI commands. You should check the return value of the mciSendString or mciSendCommand function before using a new device identifier to ensure that the identifier is valid. (You can also retrieve a device identifier by using the mciGetDeviceID function.) Like all MCI command messages, MCI_OPEN has an associated structure. These structures are sometimes called parameter blocks. The default structure for MCI_OPEN is MCI_OPEN_PARMS. Certain devices (such as waveform and overlay) have extended structures (such as MCI_WAVE_OPEN_PARMS and MCI_OVLY_OPEN_PARMS) to accommodate additional optional parameters. Unless you need to use these additional parameters, you can use the MCI_OPEN_PARMS structure with any MCI device. The number of devices you can have open is limited only by the amount of available memory. Using an Alias When you open a device, you can use the "alias" flag to specify a device identifier for the device. This flag lets you assign a short device identifier for compound devices with lengthy filenames, and it lets you open multiple instances of the same file or device. For example, the following command assigns the device identifier "birdcall" to the lengthy filename C:\NABIRDS\SOUNDS\MOCKMTNG.WAV: mciSendString("open c:\nabirds\sounds\mockmtng.wav type waveaudio alias birdcall",
lpszReturnString, lstrlen(lpszReturnString), NULL);
In the command-message interface, you specify an alias by using the lpstrAlias member of the MCI_OPEN_PARMS structure. Specifying a Device Type When you open a device, you can use the "type" flag to refer to a device type, rather than to a specific device driver. The following example opens the waveform-audio file C:\WINDOWS\CHIMES.WAV (using the "type" flag to specify the waveaudio device type) and assigns the alias "chimes": mciSendString(
"open c:\windows\chimes.wav type waveaudio alias chimes",
lpszReturnString, lstrlen(lpszReturnString), NULL);
In the command-message interface, the functionality of the "type" flag is supplied by the lpstrDeviceType member of the MCI_OPEN_PARMS structure. Simple and Compound Devices MCI classifies device drivers as compound or simple. Drivers for compound devices require the name of a data file for playback; drivers for simple devices do not. Simple devices include cdaudio and videodisc devices. There are two ways to open simple devices:
- Specify a pointer to a null-terminated string containing the device name from the registry or the SYSTEM.INI file.
lstrlen(lpszReturnString), NULL);
In this case, "videodisc" is the device name from the registry or the [mci] section of SYSTEM.INI.
- Specify the actual name of the device driver. Opening a device using the device-driver filename, however, makes the application device-specific and can prevent the application from running if the system configuration changes. If you use a filename, you do not need to specify the complete path or the filename extension; MCI assumes drivers are located in a system directory and have the .DRV filename extension.
- Specify only the device name. This lets you open a compound device without associating a filename. Most compound devices process only the capability (MCI_GETDEVCAPS) and close (MCI_CLOSE) commands when they are opened this way.
- Specify only the filename. The device name is determined from the associations in the registry.
- Specify the filename and the device name. MCI ignores the entries in the registry and opens the specified device name.
lstrlen(lpszReturnString), NULL);
In the command-string interface, you can also abbreviate the device name specification by using the alternative exclamation-point format, as documented with the open command. Opening a Device Using the Filename Extension If the open (MCI_OPEN) command specifies only the filename, MCI uses the filename extension to select the appropriate device from the list in the registry or the [mci extensions] section of the SYSTEM.INI file. The entries in the [mci extensions] section use the following form: filename_extension=device_name MCI implicitly uses device_name if the extension is found and if a device name has not been specified in the open command. The following example shows a typical [mci extensions] section: [mci extensions]
wav=waveaudio
mid=sequencer
rmi=sequencer
Using these definitions, MCI opens the waveaudio device if the following command is issued: mciSendString("open train.wav", lpszReturnString,
lstrlen(lpszReturnString), NULL);
New Data Files To create a new data file, simply specify a blank filename. MCI does not save a new file until you save it by using the save (MCI_SAVE) command. When creating a new file, you must include a device alias with the open (MCI_OPEN) command. The following example opens a new waveaudio file, starts and stops recording, then saves and closes the file: mciSendString("open new type waveaudio alias capture", lpszReturnString,
lstrlen(lpszReturnString), NULL);
mciSendString("record capture", lpszReturnString,
lstrlen(lpszReturnString), NULL);
mciSendString("stop capture", lpszReturnString,
lstrlen(lpszReturnString), NULL);
mciSendString("save capture orca.wav", lpszReturnString,
lstrlen(lpszReturnString), NULL);
mciSendString("close capture", lpszReturnString,
lstrlen(lpszReturnString), NULL);
Shareable Devices The "shareable" (MCI_OPEN_SHAREABLE) flag of the open (MCI_OPEN) command lets multiple applications access the same device (or file) and device instance simultaneously. If your application opens a device or file as shareable, other applications can also access it by opening it as shareable. The shared device or file gives each application the ability to change the parameters governing its operating state. Each time a device or file is opened as shareable, MCI returns a unique device identifier, even though the identifiers refer to the same instance. If your application opens a device or file without specifying that it is shareable, no other application can access it until your application closes it. Also, if a device supports only one open instance, the open command will fail if you specify the shareable flag. If your application opens a device and specifies that it is shareable, your application should not make any assumptions about the state of this device. Your application might need to compensate for changes made by other applications accessing the device. Most compound files are not shareable; however, you can open multiple files, or you can open a single file multiple times. If you open a single file multiple times, MCI creates an independent instance for each, with each instance having a unique operating status. If you open multiple instances of a file, you must assign a unique device identifier to each. You can use an alias, as described in the following section, to assign a unique name for each file.
- Software for developers
-
Delphi Components
.Net Components
Software for Android Developers - More information resources
-
MegaDetailed.Net
Unix Manual Pages
Delphi Examples - Databases for Amazon shops developers
-
Amazon Categories Database
Browse Nodes Database